Oil & Natural Gas Projects
Transmission, Distribution, & Refining
Sealing Large Diameter Cast Iron Pipe Joints under Live Conditions
The project will develop a new technology for the in-line repair of natural gas pipelines. The objective of this project is to design, test, and commercialize a robotic system capable of sealing multiple cast iron bell and spigot joints from a single pipe entry point. The system will affect repairs while the pipe remains in service by traveling through the pipe, cleaning each joint surface, and attaching a stainless steel sleeve lined with epoxy-impregnated felt across the joint.
Several older urban areas of the United States still have large numbers of cast-iron gas distribution mains; some 47,000 miles of cast iron pipe is still in service. Individual segments of these mains average between 12 feet and 20 feet in length and are connected to one another by a bell and spigot joint. The annular space between the bell and spigot is filled with a jute packing to provide a fluid seal and finished with a lead or cement plug.
In the days of manufactured gas, the jute material was kept moist and compliant by the humidity and higher molecular weight hydrocarbons present in this gas, and as a result, the joints were usually leak free. However, for many years now, the natural gas flowing in these mains is characterized by its low humidity and high methane purity. This has resulted in the jute drying out and cracking, producing leaks. Local gas distribution companies must extend the useful life of these cast iron mains by finding ways to fix the leaking joints inexpensively.
The robotic joint-sealing system under development here will be comprised of four main subsystems. These are: 1) two sequentially run, multiple-module robot trains; 2) pipe-access hardware for safely admitting into and removing the robot trains from the live gas-main environment; 3) a coiled tubing (CT) delivery system for providing primary locomotion, power and data communications between the in-pipe robot and 4) surface control and display electronics.
The first robot train consists of a front-mounted camera that is used to visually locate each bell and spigot joint, a counter-rotating brushing module whose function is to remove debris from the pipe wall and a final module consisting of a combination base/supplemental locomotion module. In the patch setting mode, the brush module is removed from the train and replaced with the stainless-steel patch-carrier/patch-setting module.
Gas Technology Institute (GTI) – project management and research product
Maurer Technology – use of Drilling Research Center for testing
Public Service Electric Gas Company (PSE&G) – pipeline for testing
Des Plaines, Illinois 60018
The proposed system will affect repairs while the pipe remains in service by traveling through the pipe, cleaning each joint surface, and attaching a stainless steel sleeve lined with epoxy-impregnated felt across the joint. Coiled tubing equipment will be designed to optimize the push distance from a single pipe entry point. The repair tool provides a means of internal repair of multiple pipe joints and reduces the number of excavations required, thus lowering the costs of cast iron pipe joint repair.
Successfully Installed Repair Sleeve
The complete robotic repair system was successfully tested in full-scale joint patching tests in 12-in. cast-iron joints in the laboratory. The drilling assembly for cutting an access hole through the wall of a gas main was also successfully tested. All components and systems functioned as required and field application of the robotic system is very promising.
Specific accomplishments include:
- Shop testing of the pipe inspection/wall-cleaning module under increasingly more difficult and realistic conditions. These tests were conducted in the laboratory with larger in-pipe travel distances and full exercise of control electronics and software.
- Successful testing of the patch-setting module with the latest generation of 12-inch repair sleeves. Test results were used to optimize design of the patch assembly and the patch-setting robot train. Patches were set across several 12-inch bell-and-spigot joints. To confirm patch success, the ends of these joints were then capped and the line pressurized. Leak-off test results showed the patches to be tight and 100% successful.
- Full-scale laboratory testing of 12-inch version of the cast-iron bolt-on entry fitting to allow entry into a live gas main without interrupting service to customers. The fittings were leak free and a special template was developed to assure the fitting is properly located on the main prior to bolt make-up.
- Successful testing of the hole saw used to cut an angled access hole into pressurized cast-iron pipes. The hole saw was shown to be capable of cutting access holes into ductile iron pipes in approximately 40–45 minutes with 100% retention of the coupon. Access holes in older cast-iron pipes are expected to be cut in approximately 30 minutes due to the better machinability of cast iron.
- Conducting full-up tests of the system in the shop, including cutting multiple access holes through the bolt-on fitting and setting several patches across joints in the test main.
- Implementing software controls and system displays into the LabVIEW userinterface/ robotics-control environment. The LabVIEW environment is used to control all aspects of the robot operation including camera pan, zoom, tilt, lighting, cleaning motor operation, patch setting, etc.
- Collecting additional information and data to conduct a benefit analysis. A practical cost/benefit analysis will be completed under the future field tests to be conducted with a large gas distribution company located in the Northeast United States. This company has agreed to perform a direct cost comparison of external joint encapsulation, internal spraying with an anaerobic sealant and the robotically set Link-Pipe patches.
- Planning a field test demonstration of the large-diameter robotic system currently scheduled for second quarter 2006 (after the end of the current heating season). Several discussions between GTI, MTI, Public Service Electric & Gas Company, and other utilities have been conducted for scheduling field tests. A Master Service Agreement has already been signed to allow this work to be conducted.
Current Status and Remaining Tasks:
All experimental work has been completed. The final report has been submitted and approved and the project has concluded. Full-scale field tests of the large-diameter patching system are currently being planned and will be conducted in the second quarter of 2006 in gas mains operated by Public Service Electric and Gas Company.
Project Start: March 25, 2002
Project End: September 24, 2005
DOE Contribution: $520,336
Performer Contribution: $130,084
NETL – Daniel Driscoll (email@example.com or 304-285-4717)
GTI – Kiran Kothari (firstname.lastname@example.org or 847-768-0893)
Final Report [PDF-4610KB] - December 2005 - Gas Technology Institute & Maurer Technology Inc.
June 2005 Quarterly Report: Sealing Large-Diameter Cast-Iron Pipe Joints Under Live Conditions [PDF-3574KB]
April 2005 Quarterly Report: Sealing Large-Diameter Cast-Iron Pipe Joints Under Live Conditions [PDF-3238KB]
Status Assessment: [PDF-47KB]