Goal: The goal is to develop technologies that can provide significant reductions in both the cost and environmental impact of drilling.
Objectives: The objectives are to develop and demonstrate micro-borehole drilling systems for deep exploration drilling, extend the microhole depth capability by an order of magnitude, and reduce the footprint and costs of drilling exploration and test wells.
|LANL coiled-tubing microdrilling rig (right), with mud cleaning system (rear left) and contract grout/cement mixer (front) on location at demonstration site|
Los Alamos National Laboratory (LANL) – Project management and all research products
The concept developed by LANL avoids the more complicated aspects of conventional drilling and reduces the size of the rig required. The coiled-tubing-deployed drill was selected to provide inexpensive, reliable, hard-wired, bottom-hole data and control telemetry. The basic, built-for-purpose coiled-tubing-unit (CTU) microrig is readily adaptable to support low-cost directional drilling and through-tubing micro-lateral drilling from existing wells. The drilling system will also be suitable for drilling with low density, compressible drilling fluids to penetrate depleted reservoirs, and to search for and produce bypassed oil and gas.
The LANL concept assumes that a properly designed, polycrystalline diamond compact (PDC) or thermally stable, polycrystalline diamond (TSD) drag bit will be rotated by a relatively high speed Moineau-principle, positive-displacement (drilling) motor (PDM). A robust, instrumented, near-bit-sensor sub located below the motor will support the automation and control of the bottom-hole drilling assembly. An isolation sub above the motor will protect a less robust telemetry instrumentation sub and the coiled tubing from pulsations and vibrations generated in the drilling assembly.
The LANL coiled-tubing-deployed microdrilling concept was successfully demonstrated at three sites: the Fenton Hill demonstration site near Los Alamos, a site with dry-lake-bed sediments, and the San Ysidro site in Sandoval County, NM. Based on local outcrops, it was anticipated that the San Ysidro site would provide the first application of the LANL microdrilling system to typical oil-field rocks. As it turned out, the site provided significant challenges including artesian flow, loss of returns, and severe well instability in poorly consolidated sediments, but did not provide the anticipated strata of relatively hard sandstones and shale. Problems were encountered with excessive hole washouts at the San Ysidro site, but it is believed that the development of a low-flow, high-differential-pressure drilling motor, and the stability of continuous drilling operations (rather than nightly shutdowns), will mitigate the problems.
Los Alamos presently has the capability to drill 1-3/4-inch and 2-3/8-inch holes up to 800 feet deep in unconsolidated and soft sediments with commercial PDMs. LANL can complete the holes with a cemented-in casing in stable formations, and have demonstrated the installation of casing in unstable formations with a bentonite grout.
Based on these demonstrations, modifications needed to improve the original concept have been identified. The modifications are described in a Road Map document that outlines the technologies needed to develop a capability to reach a depth of 5000 ft with a low-cost, high-performance drilling system. The advances are needed in three areas: (1) optimization of drilling hydraulics, cuttings transport, and bore-wall stabilization; (2) enhancement of drilling motors and rotary percussion hammers with compatible isolation tools; and (3) downsizing downhole sensors, instrumentation, and telemetry needed to support automated drilling, real-time steering, and logwhile-drilling. Technology requirements for microhole completions include downsizing perforation technology, and downhole cementing equipment for both coupled casing and continuous (coiled-tubing) casing.
Current Status and Remaining Tasks:
The Field Office Work Agreement with LANL funded by NETL through the Natural Gas and Oil Technology Partnership is completed. Development funding prior to and following this project has been provided from other sources. Research is continuing to prove the ability of the LANL microdrilling concepts.
For example, during 2003 LANL successfully drilled and completed the first production microwell to a depth of 497 feet at the Rocky Mountain Oilfield Technology Center (RMOTC) facility at the Teapot Dome Field in central Wyoming. The well penetrated two potential production zones, was completed with a micro version of a standard cased-hole completion design and was cemented using a traditional cementing procedure and equipment. LANL plans to drill and complete up to four seismic monitoring holes at RMOTC during 2004.
DOE is currently soliciting proposals to develop the technologies outlined in the technology Road Map document.
Project Start: April 10, 2000
Project End: March 31, 2002
Anticipated DOE Contribution: $500,000(combined FEWA08E-01/FWP-LONG1)
Performer Contribution: $0
NETL – John D. Rogers (email@example.com or 304-285-4880)
LANL – James N. Albright (firstname.lastname@example.org or 505-665-0640)