The goal is to improve the depth rating and efficiency of percussion drilling in hard rock formations by: benchmarking the performance of a several commercial fluid drilling hammer, recommending ways to improve a fluid hammer performance, and facilitating industrial acceptance and commercialization.
Downhole fluid hammer systems convert a portion of the power resident in the drilling fluid to mechanical force that drives the drill bit into the formation. While several downhole hammer tools are currently available for boreholes where air is employed as the drilling fluid, the application of hammer drilling using liquids at high or even moderate borehole pressures has experienced problems. If this technology can be more effectively developed, these so-called ?mud hammers? could be especially useful in drilling into hard rock formations found in deeper basins.
This project brings together a team of industry advisors/specialists to focus on three study areas in a controlled drilling test environment to determine the potential and best course of action for successful mud hammer commercialization. The study areas are: large-scale laboratory hammer drilling tests at reservoir conditions, benchmarking of hammer performance relative to conventional drilling, and optimization of hammer performance. Additionally a task was initiated under this project to study the effect of impact cutters on destroying a rock mass. Industry has shown significant interest in the impact tests. These impact tests were conducted to extend the understanding through basic research as to the rock breakage and cuttings removal under the dynamic loading conditions of hammer drilling.
The original industry partners for this project were SDS Digger Tools, Novatek, BP Amoco, ExxonMobil, and Pajarito Enterprises. Subsequently, PDVSA, Shell, ConocoPhillips, and Smith International have become participants.
Full-scale drilling optimization tests were performed in TerraTek?s wellbore simulator, where confining and overburden stresses are applied to the rock samples and borehole pressure is established by choking the drilling fluid flow downstream of the bit. Weight on bit is applied with a servo-controlled system. Rotary speed is controlled with variable speed direct drive motors, five-speed transmission, and a standard oil-field rotary table. The samples were 15 ½ inches wide by 36 inches long, Carthage marble and Crab Orchard sandstone, with unconfined strengths of approximately 16,000 psi and 27,000 psi, respectively. Two water-based muds (10 and 15 ppg) and 9 ppg brine were used as drilling fluids.
Terra Tek, Inc. – Project management and all research products
Salt Lake City, Utah 84101
The results will be used to improve the state of mud hammer drilling at depth and improve the understanding and ability to use mud hammers at deeper depths and at higher wellbore pressures. This knowledge is helping to redesign percussion drilling tools which have shown to drill much faster at shallower depths and lower wellbore pressures. Increasing the rate of penetration will reduce risks, drilling time and costs as well as increasing drilling efficiency, thus reducing the environmental impact of the drilling process.
A ?cutter impact testing? program examined rock removal under conditions that could offer additional insights into fluid hammer performance optimization. The focus of this work was on single cutter impact testing in pressurized mud (up to 5000 psi) and at elevated pore pressure, to better understand the cutter/rock interaction. The impact energy and duration of impact were varied to evaluate the effect of the shape of the stress wave that enters the rock sample. The performance of the cutter was evaluated by measuring the crater volume, energy partitioning, and if possible, the extent of the damaged zone under the crater. A paper was published on the results of the impact testing.
Current Status and Remaining Tasks:
This project is complete.
Project Start: September 25, 2000
Project End: September 30, 2005
DOE Contribution: $716,935
Performer Contribution: $212,000
NETL – Gary Covatch (Gary.Covatch@netl.doe.gov or 304-285-4589)
Terra Tek – Arnis Judzis (firstname.lastname@example.org or 801-584-2483)
2002 Topical Report [PDF-7606KB]
IADC/SPE 74540 "World's First Benchmarking of DrillingMud Hammer Performance at Depth Conditions." Authors - Tibbitts/Judzis/Black, TerraTek; Roy Long, DOE; Brian Miller, BP America
"Mud Hammer Performance Optimization", GTI Natural Gas Technologies II Conference 8-11 February 2004, Arizona Authors - Alan Black and A. Judzis, TerraTek
"Mud Hammers Changing the Game", Drilling, March 2003, pgs 16-18, Author - Wajid Rasheed.
Green, S,. Judzis, A., Curry, D. , Black, A., Prasad, U., and Rogers, J: “Single Cutter Impact Tests Investigate Deep-Well Hammer-Drilling Performance,” paper SPE 97173 presented at the 2005 SPE Annual Technical Conferences and Exhibition 9-12 October 2005.