Transmission, Distribution, & Refining
Gasline Network Sensor System - GASNET™

DE-FC26-02NT41320

Goal:
The goal is to help to optimize the functioning of the nation’s natural gas distribution infrastructure through the development and demonstration of the Gasline Network Sensor System (GASNET™), a distributed network of multipurpose sensors for communicating information on the real time status of a natural gas distribution network to utility operators.

Background:
GASNET™ is a wireless, self-powered network of keyhole-installed and keyhole-replaceable sensors capable of measuring and communicating key process variables such as pressure, flow, and vibration.

Motivation for this effort includes:

  • Lack of real-time distributed operating parameter information in distribution networks,
  • Costly (primarily communications equipment cost) and limited sensor products (typically pressure only) for post-construction installation,
  • The need for a better understanding of system operating behavior to carry out modeling analysis (e.g., Stoner modeling) in support of capital investment and repair activities, and
  • The need for a real-time 3rd-party warning communications system.

Schematic illustrating layout of GASNET components

Performers:
Automatika, Inc. – project management and research product
Northeast Gas Association (NGA) – access to pipeline systems for field testing purposes

Location:
Pittsburgh, Pennsylvania 15238
Field Test in West Valley, New York

Potential Impact:
A system such as GASNET™ will enable real-time monitoring of local distribution company networks with a wide sensor-suite and the potential for relatively low-cost network expansion. The data developed from such a system will be useful for improved Stoner modeling and data-logging for capital-project planning. The monitoring will help to alert system operators to safety problems and trouble spots, providing for improved operating safety and performance.

The GASNET™ system could provide increased understanding of distribution network in situ conditions, leading to cost benefits estimated to be over $10 million annually, nationwide.

ECONOMIC BENEFITS

  • Early detection of third-party intrusion reduces potential and cost of accident-damage to personnel (lawsuits) and property (insurance payouts)
  • Reduction in installation cost due to better planning ability in terms of network expansion
  • Leaner and more optimal operation of the distribution network due to real-time distributed data availability - will reflect on company's profitability and reduction in rates to customers
  • Life-extension and potential gas-loss reduction due to better monitoring - reduces capital expenditures for repairs and possible area shutdowns which in the winter can cause large costs in building damage, etc.

ENVIRONMENTAL BENEFITS

  • Avoidance/Reduction of potential natural-gas release from preventive and/or early detection of leakage or third-party intrusion
  • Reduction of excavations (and property/nature damage) due to better problem prediction and localization.

ENERGY SECURITY BENEFITS

  • Detection of unexpected conditions due to potential catastrophic leakage and real-time alarm for rapid remote shut-down activation
  • Third-party intrusion detection, whether through excavation or even visual surveillance data relayed in quasi real-time to central office
  • Usage of pipe-infrastructure for secure, fail-safe critical-component (valves, regulator, etc.) communications backbone in the case of sabotage, natural disaster, terrorist activity, etc.

Accomplishments:

  • Designed and built a pre-prototype sensor package including an in-pipe sensor wand, a pipe-penetration adapter, and computer and communication software modules,
  • Successfully completed a demonstration of the system in an outdoor aboveground test-loop, and
  • Successfully demonstrated operation of the pre-prototype sensor system on live cast iron mains.

The entire three-phase project effort for the development and field-deployment of a prototype GASNET™ system has been very successful overall. The main technologies, ranging from sensing, communications, software and display to in-field installation, safety design, real-time and off-line data logging were shown to be feasible in both cast-iron and steel mains. The project resulted in the development of three key technical subsystems (sensor-wand, electronics and power system) as well as the embedded software and graphical user interface (GUI) to collect, display and store all the measured data.

Based on these results, one can conclude that a GASNET™ system has valid applications in more than one form within the gas main distribution and transmission markets. Sensing and communications options are vast enough to cover any existing utility preference and are upgreadable as technology evolves. The use of the collectable data by the utilities has yet to be explored in depth in terms of its use as a monitoring, emergency, or even a capital-expenditure planning tool, but we believe this to be only a matter of time before utilities come up with more ways to integrate this data into their operations.

When a utility lays out a distribution system, a computer model is utilized to predict pressures and flows in the system, allowing the utility to size compressors and storage facilities. Once the pipelines are installed however, real-time monitoring of operating parameters is only done at the pumping/storage/regulating facilities. Additionally, data from individual gas meters collected over time and compared with volumes measured at the supply centers, can give some indication of the state of the network. This method of operating does not provide the level of detail and opportunity for system optimization that would be possible if a distributed network of real-time monitoring sensors were to be employed.

 

Pre-prototype sensor - part of a standalone, distribution pipeline sensor network system for real-time monitoring of live distribution gas mains

 

The contractor, in partnership with the Northeast Gas Association (NGA – formerly known as NYGAS – New York Gas Group) and its associated utilities, developed and tested a proof-of-feasibility pre-prototype for a standalone, distribution pipeline sensor network system for real-time monitoring of live distribution gas mains. The system concept addresses five key needs of gas distribution network managers: alarms for potentially-damaging encroachment by third parties, detection of substantial leaks, cost-effective monitors and sensors, a virtual model for system analysis, and improved and cost-effective data acquisition, system monitoring, and control capabilities.

The pre-prototype sensor system developed for the network consists of a pipe-internal sensor wand and an external safety housing and power supply that communicates is linked to a remote graphical user interface subsystem. The sensor wand itself consists of a single printed circuit board (PCB) potted in a machined national pipe thread (NPT) fitting. The electronics are based on a simple architecture, relying on a dedicated microprocessor to poll all the sensors on the wand, while interfacing to the wireless radio frequency (RF) electronics over a simple serial cable with a pre-established protocol.

The safety enclosure that was developed to connect to the NPT-plug is not only to protect the PCB, but also for operational safety. Utilities require that all non-certified electronics be purged and pressurized with an inert gas. The pre-prototype uses a vacuum pump to evacuate the sealed electronics enclosure and a pressurized cartridge to deliver CO2 gas through a regulator set to several psig above pipe-internal pressure.

The power subsystem consists of an enclosure with original equipment manufacturer (OEM) NiCad battery cells wired in parallel to allow for week-long field trials. The graphical user interface (GUI) was developed based on the idea of displaying a single unit’s data, while having the data for other units readily available and being able to easily switch which sensor’s wand’s data was being displayed. The software resides on an H8 micro-controller that runs custom firmware to interface to pressure, velocity, relative humidity, temperature, 2-D accelerometer, two serial communication devices and digital potentiometers. The individual units are designed to be deployed in a network mode, where each unit is a sensor-gathering node capable of transmitting its data through the pipe cavity in wireless format to another node acting as the central data-collector. Different work modes are defined to allow different levels of power conservation and interactivity of the system.

A functional demonstration of the system involved the installation of multiple units in live cast iron mains, with collection and communication of data through the pipe wirelessly to a single node used to extract and log the data. The test revealed that gas flow rates exhibit highly dynamic and oscillatory behavior across a half-mile stretch, in terms of both amplitude and direction, as a function of time-of-day. Limited pressure measurements showed pressures to be within the predicted range; however, dynamic behavior was not measurable due to premature sensor-failure. Gas temperature and water content were found to be extremely steady, with water content measured at less than one percent by volume. Mechanical pipe-wall vibration measurements proved to only be possible within the vicinity of an instrumented pipe section due to the segmented and isolating nature of the cast iron main’s bell-and-spigot design. However, measurements did show that road-traffic could be ignored, while road-surface jack hammering was readily detected, as were impact-loads as small as a pipe-wall hammer strike.

Current Status and Remaining Tasks:
The GASNET™ system was shown to be a feasible concept in terms of its technology and its capability to collect, transmit, and log data over a distributed network of sensors.

This project has been completed and a Final Report is available.

Project Start: February 26, 2002
Project End: May 31, 2006

DOE Contribution: $997,787
Performer Contribution: $1,025,379

Contact Information:
NETL – Tony Zammerilli (anthony.zammerilli@netl.doe.gov or 304-285-4641)
Automatika – Hagen Schempf (hagen@automatika.com or 412-268-6884)

Additional Information:
Final Report [PDF-2.33MB]

StayConnected Facebook Twitter LinkedIn RssFeed YouTube